5713221861/10.13
B
B2
B7
B3
B4
B5
B6
B1
B13
B8
B9
B10
B11
B12
C
D
D1
D2
C1
A18
C2
C3
C4
D3
D4
D5
D6
2
A
A1
A2
A5
A6
A3
A4
A11
A12
A7
A13
A14
A8
A9
A15
A16
A10
A22
A18
A17
A20
A19
A21
3
1
2
3
4
5
6
7
8
9
10
11
12
16
13
14
15
4
17
21
25
18
22
26
30
19
23
27
31
20
24
28
A
B
PUSH
29A
29B
H
S
PU
B
A
32
5
Making coffee using coffee beans .................................12
Making coffee using pre-ground coffee ........................13
CONTENTS
INTRODUCTION ....................................................... 7
Symbols used in these instructions .................................7
Letters in brackets...........................................................7
Troubleshooting and repairs ...........................................7
MAKING DRINKS WITH MILK................................... 13
Filling and attaching the milk container .......................13
Adjusting the amount of froth ......................................14
Making drinks with milk automatically.........................14
Cleaning the milk frother with the CLEAN button ........14
Programming the quantity of coffee and milk in the cup
for the CAPPUCCINO, LATTE, FLAT WHITE and HOT MILK
buttons ........................................................................14
Delivering hot water ....................................................15
Change the quantity of water delivered automatically. 15
Delivering steam...........................................................15
Tips for using steam to froth milk..................................15
Cleaning the spout after use .........................................15
SAFETY ................................................................... 7
Fundamental safety warnings.........................................7
DESIGNATED USE ..................................................... 7
INSTRUCTIONS ........................................................ 7
DESCRIPTION .......................................................... 8
Description of the appliance ...........................................8
Description of the control panel......................................8
Description of the milk container....................................8
Description of the accessories .........................................8
CLEANING ............................................................. 15
Cleaning the coffee grounds container..........................15
Cleaning the drip tray and condensate tray...................16
Cleaning the inside of the coffee maker ........................16
Cleaning the water tank................................................16
Cleaning the coffee spouts............................................16
Cleaning the pre-ground coffee funnel .........................16
Cleaning the infuser......................................................16
Cleaning the milk container..........................................17
Cleaning the hot water/steam nozzle ...........................17
PRELIMINARY CHECKS ............................................. 8
Checking the appliance...................................................8
Installing the appliance ..................................................8
Connecting the appliance ...............................................9
Using the appliance for the first time..............................9
TURNING THE APPLIANCE ON ................................... 9
TURNING THE APPLIANCE OFF .................................. 9
MENU SETTINGS .................................................... 10
Rinsing..........................................................................10
Descale .........................................................................10
Install filter ...................................................................10
Replacing the filter .......................................................10
Adjust time ...................................................................10
Auto-start.....................................................................10
Auto-Off........................................................................10
Cup warmer ..................................................................10
Energy Saving ...............................................................11
Setting the temperature ...............................................11
Setting water hardness.................................................11
Beep .............................................................................11
Setting the language ...................................................11
Cup lighting ..................................................................11
Default values (reset)....................................................11
Statistics function .........................................................12
DESCALE ............................................................... 17
SETTING WATER HARDNESS.................................... 18
Measuring water hardness............................................18
Set water hardness .......................................................18
WATER FILTER ....................................................... 18
Installing the filter ........................................................18
Replacing the filter .......................................................19
Removing the filter.......................................................19
TECHNICAL SPECIFICATION..................................... 19
DISPLAYED MESSAGES ........................................... 20
TROUBLESHOOTING ............................................... 21
ELECTRICAL CONNECTION (UK ONLY)....................... 23
MAKING COFFEE .................................................... 12
Selecting the coffee taste..............................................12
Selecting the quantity of coffee in the cup ...................12
Customising the “my coffee”quantity ...........................12
Adjusting the coffee mill...............................................12
Tips for a hotter coffee ..................................................12
6
•
•
•
•
Make sure the socket used is freely accessible at all times,
enabling the appliance to be unplugged when necessary.
Unplug directly from the plug only.
Never pull the power cable as you could damage it.
To disconnect the appliance completely, release the main
switch at the back of the appliance by pressing it.
If the appliance is faulty, do not attempt to repair.
Turn it off, unplug from the mains socket and contact
Customer Experience.
INTRODUCTION
Thank you for choosing this automatic espresso and cappuccino
machine.
We hope you enjoy using your new appliance.
Take a few minutes to read these instructions.
This will avoid all risks and damage to the machine.
Symbols used in these instructions
Important warnings are identified by these symbols.
It is vital to respect these warnings.
•
Iftheplugorpowercableisdamaged, itmustbereplaced
by De’Longhi Customer Experience only to avoid all risk.
Danger!
Failure to observe the warning could result in life threatening
injury from electric shock.
Important!
•
•
Keep all packaging (plastic bags, polystyrene foam) away
from children.
Important!
The appliance is not intended for use by persons (includ-
ing children) with reduced physical, sensory or mental
capabilities, or lack of experience and knowledge, unless
they have been given supervision or instruction concern-
ing use of the appliance by a person responsible for their
safety. Children must be supervised to ensure they do not
play with the appliance.
Failure to observe the warning could result in injury or damage
to the appliance.
Danger of burns!
Failure to observe the warning could result in scalds.
Please note:
This symbol identifies important advice or information for the
user.
Danger: Risk of burns!
This appliance produces hot water and steam may form while
it is in operation.
Avoid contact with splashes of water or hot steam.
Letters in brackets
The letters in brackets refer to the legend in the Description of
the Appliance on pages 2 and 3.
DESIGNATED USE
Troubleshooting and repairs
This appliance is designed and made to prepare coffee and heat
drinks.
In the event of problems, first try and resolve them following
the information given in the section “Displayed messages” on
page 20 and “Troubleshooting”on page 21.
If this does not resolve the problem or you require further
information, you should consult Customer Experience by calling
the number given on the annexed“Customer Experience”sheet.
If your country is not among those listed on the sheet, call the
number given in the guarantee.
All other use is considered improper.
This appliance is not suitable for commercial use.
The manufacturer is not liable for damage deriving from
improper use of the appliance.
This is an household appliance only.
It is not intended to be used in:
•
staff kitchen areas in shops, offices and other working
environments;
If repairs are required, contact De’Longhi Customer Experience
only. Contact details are given in the guarantee certificate
provided with the appliance.
•
•
farm houses;
by clients in hotels, motels and other residential type
environments;
SAFETY
Fundamental safety warnings
•
bed and breakfast type environments.
INSTRUCTIONS
Danger!
Read these instructions carefully before using the appliance.
This is an electrical appliance and may cause electric shock.
You should therefore respect the following safety warnings:
-
Failure to follow these instructions may result in burns or
damage to the appliance.
•
•
Never touch the appliance with damp hands or feet.
Never touch the plug with damp hands.
The manufacturer is not liable for damage deriving from
failure to respect these instructions.
7
B10. FLAT WHITE button: to deliver a flat white
B11. HOT MILK button: to deliver a cup of hot milk (When in
the settings menu, press to scroll forwards)
Please note:
Keep these instructions.
If the appliance is passed to other persons, they must also be
provided with these instructions.
B12:
B13.
button: to deliver steam
button: to make 2 cups of coffee with the
settings displayed
DESCRIPTION
Description of the appliance
(page 3 - A )
A1. Beans container lid
A2. Top lid
Description of the milk container
(page 2 - C )
D1. Froth adjustment and CLEAN dial
D2. Frothed milk spout (adjustable)
D3. Milk intake tube
A3. Grinding adjustment dial
A4. Beans container
A5. Pre-ground coffee funnel lid with pressure lock
A6. Pre-ground coffee funnel
A7. Main switch
A8. Socket for power cable connector
A9. Infuser
A10. Infuser door
A11. Cup warmer shelf
A12. Control panel
A13. Coffee spout (adjustable height)
A14. Hot water and steam nozzle
A15. Condensate tray
D4. Milk container
Description of the accessories
(page 2 - D )
D1. Pre-ground coffee measure
D2. Cleaning brush
A18. Water filter (certain models only)
D3. Cappuccino maker/hot water spout
D4. Power cable
D5. “Total Hardness Test”indicator paper
D6. Descaler
PRELIMINARY CHECKS
Checking the appliance
A16. Water tank lid
After removing the packaging, make sure the product is
complete and undamaged and that all accessories are present.
Do not use the appliance if it is visibly damaged.
Contact De’Longhi Customer Experience.
A17. Water tank
A18. Water filter (some models only)
A19. Cup tray
A20. Drip tray water level indicator
A21. Drip tray
A22. Coffee grounds container
Installing the appliance
Important!
Description of the control panel
(page 2 - B )
When installing the appliance, respect the following safety
warnings:
•
The appliance gives off heat.
A number of buttons on the panel have a double function. This is
indicated in brackets in the description.
After positioning the appliance on the worktop, leave a
space of at least 3 cm between the surfaces of the appli-
ance and the side and rear walls and at least 15 cm above
the coffee maker.
Water penetrating the coffee maker could cause damage.
Do not place the appliance near taps or sinks.
The appliance could be damaged if the water it contains
freezes.
Do not install the appliance in a room where the
temperature could drop below freezing point.
Arrange the power cable in such a way that it cannot be
damaged by sharp edges or contact with hot surfaces
(e.g. electric hot plates).
B1.
B2.
button: turns the appliance on and off
: button: to select the coffee quantity
B3. MENU button to access the menu (When in the settings
MENU, it acts as the “ESC” button to exit from the selected
function and go back to the main menu).
•
•
B4. Display: guides the user in using the appliance.
B5.
button: to deliver hot water (When in the settings
menu, press to confirm the selection)
button: to make 1 cup of coffee with the settings
displayed
aroma selection button: to select the coffee
taste
B6.
B7.
•
B8. CAPPUCCINO button: to deliver a cappuccino
B9. LATTE button: to deliver a latte (When in the settings
menu, press to scroll backwards)
8
Connecting the appliance
•
•
When making the first 5-6 cappuccinos, it is normal to
hear the noise of boiling water. After this, the noise be-
comes less.
To enjoy your coffee even more and improve the perfor-
mance of your appliance, we recommend installing a
water softener filter as described in the section “INSTALL
FILTER”. If your model is not provided with a filter, you can
request one from De’Longhi Customer Services.
Important!
Check that the mains power supply voltage corresponds to
the value indicated on the rating plate on the bottom of the
appliance.
Connect the appliance to an earthed and correctly installed
socket with a minimum current rating of 10A only.
If the power socket does not match the plug on the appliance,
have the socket replaced with a suitable type by a qualified
professional.
TURNING THE APPLIANCE ON
Please note!
Using the appliance for the first time
Before turning the appliance on, make sure the main switch on
the back of the appliance is pressed (fig. 2).
Each time the appliance is turned on, it performs an automatic
preheat and rinse cycle which cannot be interrupted.
The appliance is ready for use only after completion of this
cycle.
Please note!
•
•
Coffee has been used to factory test the appliance and it
is therefore completely normal for there to be traces of
coffee in the mill.
The machine is, however, guaranteed to be new.
You should customise water hardness as soon as possible
following the instructions in the section “Setting the wa-
ter hardness”on page 18.
Danger of burns!
During rinsing, a little hot water comes out of the coffee spouts
and is collected in the drip tray underneath.
Avoid contact with splashes of water.
1. Insert the power cable connector into the socket at the
back of the appliance and connect the appliance to the
mains electricity supply (fig. 1). Make sure the main
switch at the back of the appliance is pressed (fig. 2).
Select the desired language by scrolling forwards or backwards
using the HOT MILK or LATTE button, or alternatively waiting
for the language options to scroll automatically on the display
(about every 3 seconds):
2. When “English” appears, press and hold the
button (fig. 3) for a few seconds until “English set” is dis-
played.
Follow the instructions displayed by the appliance:
3. “FILL TANK!”: remove the water tank (fig. 4), fill to the
MAX line with fresh water (fig. 5) then replace in the ap-
pliance.
•
To turn the appliance on, press the
button (fig. 7).
The message “Heating up... Please wait”is displayed.
After heating, the message “Rinsing...” is displayed. As well as
heating the boiler, the appliance also heats the internal circuits
by circulating hot water.
The appliance has reached the required temperature when a
message is displayed indicating the coffee taste and quantity.
TURNING THE APPLIANCE OFF
Whenever the coffee machine is turned off after being used to
make coffee, it performs an automatic rinse cycle.
Danger of burns!
During rinsing, a little hot water flows from the coffee spouts.
Avoid contact with splashes of water.
4. “INSERT WATER SPOUT!”: Check that the hot water spout is
inserted on the nozzle and place a container with a mini-
mum capacity of 100 ml underneath (fig. 6).
5. “Hot water... Press OK?”is displayed;
6. Press the
To turn the appliance off, press the
button (fig. 7). The ap-
pliance performs a rinse cycle, then the message “Turning off
underway Please wait...” is displayed and the appliance goes
off (standby).
button to confirm (fig. 3). The appliance
delivers water from the spout then goes off automatically.
The coffee maker is now ready for normal use.
Please note!
Please note!
If the appliance is not used for an extended period, switch off
the machine at the main switch.
•
When using the appliance for the first time, you need to
make 4-5 cups of coffee or 4-5 cappuccinos before the ap-
pliance starts to give satisfactory results.
•
first turn the appliance off by pressing the
(fig. 8);
button
9
•
release the main switch at the side of the appliance (fig.
2).
Auto-start
You can set the auto-start time in order to have the appliance
ready at a certain time (for example in the morning) so you can
make coffee immediately.
Important!
Never press the main switch while the appliance is on.
Please note!
To enable this function, the time must already have been set
correctly.
MENU SETTINGS
When you access the programming menu by pressing the
MENU/ESC button, the following menu items are available:
To enable Auto-on, proceed as follows:
1. Press the MENU/ESC button to enter the menu;
2. Press the HOT MILK or LATTE button (fig. 8) until “Au-
to-start”is displayed;
Rinsing
Use this function to deliver hot water from the spout to heat
the internal circuit and make the coffee delivered hotter.
To enable the function, proceed as follows:
1. Press the MENU/ESC button to enter the menu;
2. Press the HOT MILK or LATTE button (fig. 8) until “Rins-
ing”is displayed;
3. Press the
played;
4. Press the
3. Press the
4. Press the
button. “Enable?”is displayed;
button to confirm;
5. Press the HOT MILK or LATTE button to choose the hours;
6. Press the button to confirm;
7. Press the HOT MILK or LATTE button (fig. 8) to change
button. The message “Confirm?” is dis-
the minutes;
8. Press the
button to confirm;
(fig. 3): after a few seconds, hot water
9. Press the MENU/ESC button to exit the menu.
Once the time has been confirmed, enabling of auto-start is in-
flows out of the spout, heating the internal circuit and ma-
king the coffee delivered hotter.
dicated by the
symbol displayed alongside the time and
under the Auto-start item in the menu.
To disable the function:
1. Select auto-start from the menu;
Please note!
Press any button to stop hot water delivery at any time.
2. Press the
3. Press the
button. “Disable?”is displayed;
button to confirm.
Descale
For instructions on descaling, see page 17.
The
symbol is no longer displayed.
Install filter
Auto-Off
For instructions on how to install the filter, see the section
“Installing the filter (page 18).
The time can be changed so that the appliance switches off
after 15 or 30 minutes, or after 1, 2 or 3 hours.
To re-programme Auto-off, proceed as follows:
1. Press the MENU/ESC button to enter the menu;
2. Press the HOT MILK or LATTE button (fig. 8) until “Au-
to-off”is displayed;
Replacing the filter
For instructions on how to replace the filter, see the section
“Replacing the filter”(page 19).
Adjust time
3. Press the
button;
To adjust the time on the display, proceed as follows:
1. Press the MENU/ESC button to enter the menu;
2. Press the HOT MILK or LATTE button (fig. 8) until “Adjust
time”is displayed;
4. Press the HOT MILK or LATTE button (fig. 8) until the de-
sired operation time is displayed (15 or 30 minutes, or 1, 2
or 3 hours);
5. Press the
button to confirm;
3. Press the
button (fig. 3);
6. Press the MENU/ESC button to exit the menu.
Auto-off is programmed.
4. Press the HOT MILK or LATTE button (fig. 8) to change
the hours;
5. Press the
button to confirm;
Cup warmer
This function enables or disables the cup warmer.
Proceed as follows:
1. Press the MENU/ESC button to enter the menu;
2. Press the HOT MILK or LATTE button (fig. 8) until “Cup
warmer”appears on the display;
6. Press the HOT MILK or LATTE button (fig. 8) to change
the minutes;
7. Press the
This sets the time. Press the MENU/ESC button to exit the
menu.
button to confirm.
10
3. Press the
button. “Disable?”is displayed (or “En-
button to disable (or enable) the func-
Beep
able?”if the function has been disabled);
4. Press the
tion.
This enables or disables the beep emitted by the machine
each time the buttons are pressed or an accessory is inserted/
removed. The beep is enabled by default.
To disable or re-enable the beep, proceed as follows:
1. Press the MENU/ESC button to enter the menu;
2. Press the HOT MILK or LATTE button (fig. 8) until “Beep”
is displayed;
5. Press the MENU/ESC button to exit the menu.
Warming the cups keeps the coffee hot.
Energy Saving
Use this function to enable or disable energy saving mode.
When enabled, the function reduces energy consumption in
compliance with European regulations.
To disable (or enable) “energy saving” mode, proceed as
follows:
3. Press the
played;
button. “ Disable?” or “ Enable?” is dis-
4. Press the
button to enable or disable the beep;
5. Press the MENU/ESC button to exit the menu.
1. Press the MENU/ESC button to enter the menu;
2. Press the HOT MILK or LATTE button (fig. 8) until“Energy
saving”is displayed;
Setting the language
To change the language for the display, proceed as follows:
1. Press the MENU/ESC button to enter the menu;
2. Press the HOT MILK or LATTE button (fig. 8) until “Set
language”is displayed;
3. Press the
button. “Disable?”is displayed (or “En-
able?”if the function has been disabled);
4. Press the
saving mode;
button to disable (or enable) energy
3. Press the
button;
4. Press the HOT MILK or LATTE button until the required
5. Then press the MENU/ESC button to exit the menu.
When the function is enabled, if the machine is not used for
about 1 minute, “Energy Saving”is displayed.
language is displayed;
5. Press the
button to confirm;
6. A message confirming the language installed is displayed;
7. Then press the MENU/ESC button to exit the menu.
Please note!
Cup lighting
•
•
•
When in energy saving mode, a few seconds elapse
before the first coffee, cappuccino or milk based coffee is
delivered as the appliance must heat up again.
To prepare any drink, press any button to exit energy
saving, then press the button corresponding to the drink
you want to make.
This function enables or disables the cup lighting. The lighting
is enabled by default.
The lights come on each time coffee and drinks with milk are
made and during each rinse cycle.
To disable or re-enable this function, proceed as follows:
1. Press the MENU/ESC button to enter the menu;
2. Press the HOT MILK or LATTE button (fig. 8) until “Cup
lighting”is displayed.
3. Press the
played;
If the milk container is inserted, “Energy saving” is not
activated.
Setting the temperature
To modify the temperature of the water used to make the cof-
fee, proceed as follows:
1. Press the MENU/ESC button to enter the menu;
2. Press the HOT MILK or LATTE button (fig. 8) until “Set
temperature”is displayed;
button. “ Disable?”or“ Enable?” is dis-
4. Press the
lighting;
5. Press the MENU/ESC button to exit the menu.
button to enable or disable the cup
Default values (reset)
3. Press the
button;
This resets all menu settings and programmed quantities back
to the default values (with the exception of the language
which remains as previously set).
4. Press the HOT MILK or LATTE button until the required
temperature (●= low; ●●●●= high) is displayed;
5. Press the
button to confirm;
To reset the default values, proceed as follows:
1. Press the MENU/ESC button to enter the menu;
2. Press the HOT MILK or LATTE button (fig. 8) until “De-
fault values”is displayed;
6. Press the MENU/ESC button to exit the menu.
Setting water hardness
For instructions on setting water hardness, see page 20.
3. Press the
button;
4. The message “Confirm?”is displayed.
11
To modify this quantity, proceed as follows:
1. Place a cup under the coffee spouts (fig. 14).
5. Press the
button to confirm and exit.
Statistics function
This displays statistics relating to the machine.
To display, proceed as follows:
2. Press the
is displayed.
3. Keep the
button (fig. 10) until “MY COFFEE”
button (fig. 11) pressed until the message
1. Press the MENU/ESC button to enter the menu;
2. Press the HOT MILK or LATTE button (fig. 8) until “Statis-
tics”is displayed;
“1 MY COFFEE Program quantity” is displayed and coffee
delivery begins. Release the button.
4. As soon as the coffee in the cup reaches the required level,
3. Press the
button;
press the button
(fig. 11) again.
4. Press the HOT MILK or LATTE button (fig. 8) to verify:
The quantity of coffee in the cup has now been programmed.
-
-
how many coffees have been made;
the total number of cappuccinos and milk based coffees
made;
Adjusting the coffee mill
The coffee mill is preset in the factory to make coffee correctly
and should not require adjusting initially.
However, if after making the first few coffees you find that the
coffee is too thin and not creamy enough or that delivery is too
slow (a drop at a time), this can be corrected by adjusting the
grinding adjustment dial (fig. 12).
-
-
-
the total number of litres of water delivered;
how many times the machine has been descaled;
how many times the water softener filter has been re-
placed.
5. Press the MENU/ESC button twice to exit the menu.
Please note!
MAKING COFFEE
The grinding adjustment dial must only be turned when the
coffee mill is in operation.
Selecting the coffee taste
he appliance is set by default to make coffee with a standard
taste.
You can also choose one of these tastes:
Extra-mild taste
Mild taste
Standard taste
Strong taste
Extra-strong taste
To change the taste, press the
If the coffee is delivered too slowly or
not at all, turn one click clockwise to-
wards “7”.
For fuller bodied creamier coffee on the
other hand, turn one click anticlockwise
towards“1”(do not turn more than one
click at a time otherwise the coffee could be delivered a drop
at a time).
button (fig. 9) repeat-
These adjustments will only be evident after at least 2 cups of
coffee have been delivered.
edly until the required taste is displayed.
Selecting the quantity of coffee in the cup
The appliance is set by default to make a standard quantity of
coffee. To select the quantity of coffee, press the
button (fig. 10) until the message corresponding to the
required quantity of coffee is displayed:
If this adjustment does not obtain the desired result, turn the
dial another click.
Tips for a hotter coffee
For a hotter coffee, before delivery you are recommended to:
•
•
•
perform a rinse cycle by selecting the“Rinsing”function in
the settings menu (page 10)
warm the cups with hot water (using the hot water
function);
increase the coffee temperature in the settings menu
(page 11).
Coffee selected
Quantity in cup (ml)
MY COFFEE
Programmable:
from ≃20 to ≃180
SHORT
STANDARD
LONG
≃40
≃60
≃90
≃120
Making coffee using coffee beans
EXTRA LONG
Important!
Do not use caramelised or candied coffee beans as they could
stick to the coffee mill and make it unusable.
Customising the “my coffee” quantity
The appliance is set by default to automatically deliver 30 ml
of “my coffee”.
1. Place coffee beans in the coffee bean container (fig. 13).
12
2. Place under the coffee dispensing spouts, either:
- 1 cup if you want one coffee (fig. 14);
2. Open the beans container lid; then open the pre-ground
coffee funnel lid by pushing on PUSH and, once released,
open the lid.
- 2 cups if you want 2 coffees.
3. Lower the spouts as near as possible to the cup. This
makes a creamier coffee (fig. 15).
3. Make sure the funnel is not blocked, then add one level
measure of pre-ground coffee (fig. 17).
4. Press the button corresponding to the number of coffees
4. Place a cup under the coffee spouts.
required (1 cup
16).
or 2 cups
, figs. 11 and
5. Press the 1 cup coffee button
(fig. 11).
6. Preparation begins. The amount of coffee selected is dis-
played together with a progress bar which gradually fills
as preparation progresses.
5. Preparation begins. The amount of coffee selected is dis-
played together with a progress bar which gradually fills
as preparation progresses.
Please note!
Please note:
If“Energy saving”mode is enabled, you may have to wait a few
seconds before the first coffee is delivered.
•
•
While the machine is making coffee, delivery can be inter-
rupted at any moment by pressing any button.
At the end of delivery, to increase the quantity of coffee
in the cup, just press (within 3 seconds) one of the coffee
MAKING DRINKS WITH MILK
Please note!
buttons (
or
).
•
To avoid producing milk with poor froth or large bubbles,
always clean the milk container lid and hot water nozzle
as described in the section “Cleaning the milk container”
on pages 17.
Once the coffee has been made, the appliance is ready to make
the next drink.
Please note!
•
Various alarm messages could be displayed while using
the machine (FILL TANK, EMPTY GROUNDS CONTAINER,
etc.). Their meaning is explained in the section“Displayed
messages”(page 20).
For hotter coffee, see the section “Tips for a hotter coffee”
(page 12).
If the coffee is delivered a drop at a time, too weak and not
creamy enough or too cold, read the tips in the “Trouble-
shooting”section on page 21.
Filling and attaching the milk container
1. Remove the lid (fig. 18);
2. Fill the milk container with a sufficient quantity of milk,
not exceeding the MAX level marked on the container (fig.
19). Each mark on the side of the container corresponds
to 100 ml of milk.
•
•
Please note!
•
•
For a denser more even froth, you should use skimmed or
partially skimmed milk at refrigerator temperature (about
5°C).
If“energy saving”mode is enabled, you may have to wait
a few seconds before the first cappuccino is delivered.
Making coffee using pre-ground coffee
Important!
•
Never add pre-ground coffee
when the machine is off or it
could spread through the inside
of the machine and dirty it.
This could damage the
appliance.
3. Make sure the milk intake tube is correctly inserted in the
bottom of the milk container lid (fig. 20).
4. Place the lid back on the milk container.
5. Remove the hot water spout from the nozzle, by pressing
the button.
6. Attach the container to the nozzle and push as far as it
will go (fig. 21). The machine emits a beep (if the beep
function is enabled).
7. Place a sufficiently large cup under the coffee and frothed
milk spouts. Adjust the length of the milk spout. To move
it nearer the cup, simply pull it downwards (fig. 22).
8. Follow the instructions below for each function.
•
Never use more than 1 level measure or it could dirty the
inside of the coffee maker or block the funnel.
Please note!
If you use pre-ground coffee, you can only make one cup
of coffee at a time.
1. Press the
button (fig. 7) repeatedly until “Pre-
ground”is displayed.
13
Adjusting the amount of froth
“SET DIAL TO CLEAN” flashes on the display each time you use
a milk function. To eliminate all milk residues, proceed as fol-
lows:
1. Leave the milk container in the machine (you do not need
to empty it);
2. Place a cup or other recipient under the frothed milk
spout.
3. Turn the froth adjustment dial to “CLEAN” (fig. 22). A
progress bar appears and gradually fills as the operation
proceeds together with“Cleaning underway, Please wait”.
Cleaning stops automatically.
Turn the froth adjustment dial on the milk container lid to
adjust the amount of froth on the milk delivered while making
drinks with milk.
Dial
Description
Recommended for…
position
No froth
LATTE/
HOT MILK
Min. froth
FLAT WHITE
4. Turn the dial back to one of the froth selections.
5. Remove the milk container and always clean the steam
connection nozzle with a sponge.
Max. froth
CAPPUCCINO/ HOT MILK
(FROTHED MILK)
Please note!
Making drinks with milk automatically
The CAPPUCCINO, LATTE, FLAT WHITE and HOT MILK buttons
on the control panel enable these drinks to be prepared
automatically.
•
Toprepareanumberofcappuccinosormilkbasedcoffees,
clean the milk container after you have prepared the last
drink only.
The milk container can be kept in the refrigerator.
In some cases, to clean you must wait for the appliance to
heat up.
•
•
Proceed as follows:
1. Fill the milk container and attach it as described above.
2. Turn the froth adjustment dial on the milk container lid to
the position corresponding to the required froth.
3. Press the button corresponding to the required drink.
The name of the drink selected is displayed together
with a progress bar which gradually fills as preparation
progresses.
Programming the quantity of coffee and milk in the
cup for the CAPPUCCINO, LATTE, FLAT WHITE and HOT
MILK buttons
The appliance is set by default to automatically deliver
standard quantities.
4. After a few seconds, frothed milk is delivered from the
milk spout into the cup below. For drinks with coffee, the
machine automatically makes the coffee after delivering
the milk.
To change these quantities, proceed as follows:
1. Place a cup under the coffee and milk spouts.
2. Press and hold the button corresponding to the drink you
want to programme until the message “PROGRAM MILK
Program quantity”is displayed.
Please note!
3. Release the button.
•
•
If during delivery you want to stop preparation, press the
corresponding button.
At the end of delivery, to increase the quantity of milk or
coffee in the cup, just press (within 3 seconds) the button
corresponding to the drink being made.
The appliance starts delivering milk.
4. Once the required quantity of milk has been delivered into
the cup, press the button again.
5. The appliance stops delivering milk and after a few sec-
onds the coffee is delivered into the cup. “PROGRAM COF-
FEE Program quantity”is displayed.
6. Once the required quantity of coffee has been delivered
into the cup, press the button.
•
Do not leave the milk container out of the refrigerator for
long periods. The warmer the milk (5°C is ideal), the poor-
er the quality of froth produced.
Coffee delivery stops.
Cleaning the milk frother with the CLEAN button
The machine is now reprogrammed with the new quantities
of milk and coffee.
Important! Danger of burns
When cleaning the internal tubes of the milk container, a little
hot water and steam leak out of the frothed milk spout.
Avoid contact with splashes of water.
DELIVERING HOT WATER AND STEAM
Important! Danger of burns.
Never leave the machine unsupervised while delivering hot
water or steam.
14
The spout becomes hot during delivery. Hold by the handle
only.
•
•
•
For a richer denser froth, use skimmed or partially
skimmed milk at refrigerator temperature (about 5°C).
For a creamier froth, rotate the container with slow
movements in an upward direction.
To avoid milk with poor froth or large bubbles, always
clean the spout as described in the following section.
Please note!
If“Energy Saving”mode is enabled, you may have to wait a few
seconds before the hot water or steam is delivered.
Delivering hot water
1. Make sure the hot water spout is attached correctly (fig.
Cleaning the spout after use
Always clean the spout after use to avoid the build-up of milk
residues and prevent the spout from clogging.
6).
2. Place a container under the spout (as close as possible to
avoid splashes).
1. Place a container under the cappuccino maker and press
3. Press the
button (fig. 3).“Hot water”is displayed,
the
button to deliver a little water (fig. 3).
together with a progress bar which fills gradually as
preparation proceeds.
Stop the flow of water by pressing the
again.
button
4. The machine delivers 250 ml of hot water, then delivery
stops automatically.
2. Wait a few minutes for the cappuccino maker to cool
down, then extract the hot water spout.
To interrupt delivery of hot water manually, press the
button again.
Hold the spout with one hand by pressing the button and
with the other, turn the cappuccino maker anticlockwise
(fig. 24) and pull it downwards to remove it.
3. Also remove the steam nozzle by pulling it downwards
(fig. 25).
4. Check the hole shown by the arrow in fig. 25 is not
blocked. If necessary, clean with a pin.
5. Wash all parts of the cappuccino maker thoroughly with a
sponge and warm water.
Change the quantity of water delivered automatically.
The machine is set by default to automatically delivery 250 ml
of hot water. To modify these quantities, proceed as follows:
1. Position a container under the spout.
2. Press the
quantity”is displayed, then release the
3. When the hot water in the cup reaches the required level,
press the button again.
button again until“Hot water Program
button.
6. Reinsert the nozzle and replace the cappuccino maker on
the nozzle, turning it and pushing it upwards until it is
attached.
The machine is now reprogrammed with the new quantity.
Delivering steam
1. Make sure the hot water spout is attached correctly (fig.
6).
2. Fill a container with the liquid to be heated/frothed and
immerse the spout/cappuccino maker in the liquid.
3. Press the
out of the cappuccino maker and heats the liquid; “STE-
AM”is displayed.
4. When the required temperature is obtained, interrupt
CLEANING
Important!
•
Do not use solvents, abrasive detergents or alcohol to
clean the coffee maker.
button: after a few seconds, steam comes
With De’Longhi bean to cup coffee makers, you need not
use chemical products to clean the machine.
None of the components can be washed in a dishwasher
apart from the milk container (D).
Do not use metal objects to remove encrustations or cof-
fee deposits as they could scratch metal or plastic surfac-
es.
•
•
steam delivery by pressing the
(You should not discharge steam for more than 3 minutes
at a time).
button again.
Important!
Cleaning the coffee grounds container
When“EMPTY GROUNDS CONTAINER”is displayed, the grounds
container must be emptied and cleaned.
Always stop steam delivery before extracting the container
containing the liquid to avoid burns from splashes.
Until the grounds container has been cleaned, the appliance
continues to display the message and coffee cannot be made.
Tips for using steam to froth milk
•
Whenchoosingthesizeofthecontainer,bearinmindthat
the liquid doubles or triples in volume.
Important! Danger of burns
15
If you make a number of cappuccinos one after the other, the
metal cup tray becomes hot.
Wait for it to cool down before touching it and handle it from
the front only.
Cleaning the water tank
1. Clean the water tank (A17) regularly (about once a month
and whenever you replace the water softener filter (if
provided) with a damp cloth and a little mild washing up
liquid.
To clean (with the machine on):
2. Remove the filter (if present) and rinse with running
water.
3. Replace the filter (if provided), fill the tank with fresh wa-
ter and replace the tank.
•
•
Remove the drip tray (fig. 26), empty and clean.
Empty the grounds container and clean thoroughly to
remove all residues left on the bottom. This can be done
with the spatula on the brush provided.
Cleaning the coffee spouts
1. Regularly clean the coffee spouts with a sponge or cloth
(fig. 29A).
•
Check the condensate tray (red) and empty if necessary.
Important!
When removing the drip tray, the grounds container must be
emptied, even if it contains few grounds.
2. Check the holes in the coffee spout are not blocked. If
necessary, remove coffee deposits with a toothpick (fig.
29B).
If this is not done, when you make the next coffees, the
grounds container may fill up more than expected and clog the
machine.
Cleaning the pre-ground coffee funnel
Check regularly (about once a month ) that the pre-ground
coffee funnel (A6) is not blocked. If necessary, remove coffee
deposits with the brush (D2) supplied.
Cleaning the drip tray and condensate tray
Important!
Cleaning the infuser
The infuser (A11) must be cleaned at least once a month.
The drip tray is fitted with a level indicator (red) showing the
level of water it contains (fig. 27).
Before the indicator protrudes from the cup tray, the drip tray
must be emptied and cleaned, otherwise the water may over-
flow the edge and damage the appliance, the surface it rests on
or the surrounding area.
Important!
The infuser may not be extracted when the machine is on.
1. Make sure the machine is correctly turned off (see “Turn-
ing the appliance off”on page 9).
To remove the drip tray:
2. Remove the water tank.
1. Remove the drip tray and the grounds container (fig. 26);
2. Empty the drip tray and grounds container and wash
them;
3. Check the red condensate tray and empty if necessary.
4. Replace the drip tray and grounds container.
3. Open the infuser door (fig. 30) on the right side.
4. Press the two red release buttons inwards and at the same
time pull the infuser outwards (fig. 31).
5. Soak the infuser in water for about 5 minutes, then rinse
under the tap.
Important!
Cleaning the inside of the coffee maker
RINSE WITH WATER ONLY
Danger of electric shock!
NO WASHING UP LIQUID - NO DISH WASHER
Clean the infuser without using washing up liquid as it
could be damaged.
Before cleaning internal parts, the machine must be turned
off (see “Turning off”) and unplugged from the mains power
supply.
6. Use the brush (D2) to remove any coffee residues left in
the infuser housing, visible through the infuser door.
7. After cleaning, replace the infuser by sliding it onto the
internal support; then push the PUSH symbol fully in until
it clicks into place.
Never immerse the coffee maker in water.
1. Check regularly (about once a month) that the inside of
the appliance (accessible after removing the drip tray) is
not dirty. If necessary, remove coffee deposits with the
brush provided or a sponge.
infuser support
2. Remove the residues with a vacuum cleaner (fig. 28).
16
6. Check that the intake tube
and spout are not clogged
with milk residues.
7. Replace the dial (in
correspondence to the word
“INSERT”), spout and milk
intake tube.
Please note!
If the infuser is difficult to insert, before insertion, adapt it to
the right size by pressing the two levers shown in the figure.
Large lever
Small lever
8. Place the lid back on the milk
container.
Cleaning the hot
water/steam nozzle
Each time you prepare
milk, clean the nozzle
with a sponge to remove
milk residues from the
gaskets (see figure
alongside).
7. Once inserted, make sure the two red buttons have
snapped out.
PUSH
DESCALE
Descale the machine when the message “DESCALE” flashes on
the display.
8. Close the infuser door.
9. Replace the water tank.
Important!
•
•
Descaler contains acids which may irritate the skin
and eyes. It is vital to follow the manufacturer’s safety
warnings given on the descaler pack and the warnings
relating to the procedure to follow in the event of contact
with the skin and eyes.
You should use De’Longhi descaler only. Using unsuitable
descaler and/or performing descaling incorrectly may
result in faults not covered by the manufacturer’s guaran-
tee.
Cleaning the milk container
Clean the milk container each time
you prepare milk as described
below:
1. Remove the lid.
2. Remove the milk spout and
intake tube.
3. Turn the froth adjustment
dial clockwise to the “INSERT”
position (see figure) and pull
off upwards
4. Wash all the components
thoroughly with hot water
and mild washing-up liquid.
All components are dishwash-
er safe, placing them in the
top basket of the dishwasher.
Make sure there are no milk
residues on the hollow and
groove under the dial (see
figure alongside). If neces-
sary, scrape the groove with a
toothpick.
1. Turn the machine on.
2. Press the MENU/ESC button to enter the menu.
3. Press the HOT MILK or LATTE button until “Descale” is
displayed.
4. Select by pressing the
firm?” is displayed. Press
function.
5. The message “Add descaler Confirm?” is displayed, alter-
nating with“EMPTY THE DRIP TRAY”and“REMOVE FILTER”
(if the filter is present).
6. Completely empty the water tank (A17) and remove the
water filter (if present). Empty the drip tray (fig. 26) and
grounds container, then put back in the appliance.
7. Pour the descaler into the tank up to the level A (corre-
sponding to a 100 ml pack) marked on the side of the tank
(fig. 32), then add water (one litre) up to level B (fig. 32).
replace the water tank.
. button: “Descale Con-
again to enable the
5. Rinse inside the froth adjust-
ment dial seat with running
water (see figure)
17
8. Place an empty container with a minimum capacity of 1.5
litres under the hot water spout (fig. 4).
soft water ●
Important! Danger of burns
Hot water containing acid flows from the spout. Avoid contact
with splashes of water.
slightly hard water ●●
hard water ●●●
9. Press the
the solution.
button to confirm that you have added
The message “Descale underway”is displayed.
The descale programme starts and the descaler liquid
comes out of the water spout.
The descale programme automatically performs a series
of rinses and pauses to remove limescale deposits from
inside the machine.
very hard water ●●●●
Set water hardness
1. Press the MENU/ESC button to enter the menu.
2. Press the HOT MILK or LATTE button to select “Water
Hardness”.
3. Confirm the selection by pressing the
4. Press the HOT MILK or LATTE button and set the hard-
button.
After about 30 minutes, the message “Rinsing”“INSERT FILTER”
(if present), “FILL TANK”is displayed.
ness shown by the indicator paper (see previous section).
10. The appliance is now ready for rinsing through with clean
water. Extract the water tank, empty, rinse under running
water, fill with clean water up to the MAX level, insert the
filter (if removed previously) and put the water tank back
in the machine. “Rinsing Confirm?”is displayed.
11. Empty the container used to collect the descaler solution
and replace it empty under the cappuccino maker.
5. Press the
button to confirm the setting.
6. Press the MENU/ESC button to exit the menu.
The machine is now reprogrammed with the new water hard-
ness setting.
WATER FILTER
Certain models are fitted with a water softener filter. If this
is not the case with your model, you are recommended to
purchase one from De’Longhi Customer Experience.
To use the filter correctly,
follow the instructions be-
low.
12. Press the
button to start rinsing. Hot water flows
out of the spout and the message “Rinsing Please wait”is
displayed.
13. When the water tank is completely empty, the message
“Rinsing complete Confirm?”is displayed.
33
14. Press the
button.
15. “Heating up Please wait”is displayed, at the end of which
the machine will be ready for use.
Installing the filter
1. Remove the filter from
the packaging.
2. Turn the date indicator
disk (see fig. 33) until
the next 2 months of
use are displayed.
SETTING WATER HARDNESS
The DESCALE message is displayed after a period of time
according to water hardness.
The machine is factory set for a hardness value of 4.
The machine can also be programmed according to the hard-
ness of the mains water in the various regions so that the ma-
chine needs to be descaled less often.
Please note
34
The filter lasts about two
months if the appliance is
used normally. If the coffee
maker is left unused with
the filter installed, it will last
a maximum of three weeks.
3. To activate the filter,
run tap water through
Measuring water hardness
1. Remove the“total hardness test”indicator paper attached
to this manual from its pack.
2. Immerse the paper completely in a glass of water for one
second.
3. Remove the paper from the water and shake lightly.
After about a minute, 1, 2, 3, or 4 red squares form, de-
pending on the hardness of the water. each square corre-
sponds to one level.
the hole in the filter as
shown in the figure un-
til water comes out of
18
the openings at the side
for more than a minute
(fig. 34).
6. Press the
7. The message “Confirm?”is displayed.
8. Press the
9. “Hot water… Confirm?”is displayed.
button;
35
button to confirm the selection;
4. Extract the tank from the
appliance and fill with
water.
10. Press the
button to confirm the selection. the
appliance begins delivering hot water and the message
5. Insert the filter in the
water tank and immerse
it completely for about
ten minutes, sloping it to
enable the air bubbles to
escape (fig. 35).
6. Insert the filter in the fil-
ter housing and press as
far as it will go (fig. 36A)
7. Close the tank with the
lid, then put the tank
back in the machine (fig.
36B).
“Please wait “ is displayed.
11. After delivery, the appliance returns automatically to the
“ready for coffee”position.
The new filter is now active and you can use the coffee maker.
36A
36B
Removing the filter
If you want to continue using the appliance without a filter,
you must remove it and notify the appliance of its removal as
follows:
1. Extract the tank and exhausted filter;
2. Press the MENU/ESC button to enter the menu;
3. Press the HOT MILK or LATTE button (fig. 8) until “Install
filter Enabled”is displayed;
When you install the filter,
you must notify the appliance
of its presence.
4. Press the
5. “Disable?”is displayed;
6. Press the button to confirm and the MENU/ESC
button to exit the menu.
button
8. Press the MENU/ESC button to enter the menu;
8. Press the HOT MILK or LATTE button (fig. 8) until “Install
filter”is displayed;
TECHNICAL SPECIFICATION
10. Press the
11. The message “Enable?”is displayed.
12. Press the button to confirm the selection. “Hot
water Confirm?”is displayed;
button;
Voltage:
220-240 V~ 50/60 Hz max. 10A
Absorbed power:
Pressure:
Water tank capacity:
Size Lxhxd:
Cable length:
Weight:
1450W
15 bar
2.0 litres max.
238x350x445 mm
1.80 m
13. Position a container under the hot water spout (min. ca-
pacity: 500 ml);
14. Press the
button to confirm the selection. The
11.8 kg
appliance begins hot water delivery and the message
“Please wait”is displayed;
Beans container capacity:
250 g max.
15. After delivery, the appliance returns automatically to the
“Ready for coffee”position.
The appliance complies with the following EC
directives:
The new filter is active. You can now use the coffee maker.
•
•
EC Regulation 1275/2008 for standby;
Low Voltage Directive 2006/95/EC and subsequent
amendments;
EMC directive 2004/108/EC and subsequent amendments
Materials and accessories coming into contact with food
conform to eec regulation 1935/2004.
Replacing the filter
When “REPLACE FILTER” is displayed, after two months (see
date indicator) or when the appliance has not been used for 3
weeks, you should replace the filter:
•
•
1. Extract the tank and exhausted filter;
2. Take the new filter out of its packet and proceed as
illustrated in points 2, 3, 4, 5 and 6 in the previous section.
3. Position a container with a minimum capacity of 500 ml
under the hot water spout.
4. Press the MENU/ESC button to enter the menu;
5. Press the HOT MILK or LATTE button until “Replace filter
“ is displayed.
DISPOSAL
In compliance with European directive 2002/96/EC,
the appliance must not be disposed of with hou-
sehold waste, but taken to an authorised waste se-
paration and recycling centre.
19
DISPLAYED MESSAGES
DISPLAYED MESSAGE
POSSIBLE CAUSE
SOLUTION
FILL TANK
Insufficient water in the tank.
Fill the tank with water and/or insert it
correctly, pushing it as far as it will go until it
clicks into place.
EMPTY GROUNDS CONTAINER The grounds container (A22) is full.
Empty the grounds container and drip tray,
clean and replace. Important: when removing
the drip tray, the grounds container must be
emptied, even if it is not completely full.
If this is not done, when you make the next
coffees, the grounds container may fill up more
than expected and clog the machine.
GROUND TOO FINE ADJUST
MILL
The grinding is too fine and the coffee is
delivered too slowly or not at all.
The grinding is too fine and the coffee is
delivered too slowly or not at all.
Repeat coffee delivery and turn the grinding
adjustment dial (fig. 10) one click clockwise to-
wards “7” while the coffee mill is in operation.
If after making at least 2 coffees delivery is
still too slow, repeat the correction procedure,
turning the grinding adjustment dial another
click until delivery is correct (see the section:
“Adjusting the coffee mill” on page 12). If the
problem persists, make sure the water tank is
fully inserted, press the
button and
deliver a little water from the spout.
INSERT GROUNDS CONTAINER After cleaning, the grounds container has not Remove the drip tray and insert the grounds
container.
been replaced.
ADD PRE-GROUND COFFEE
With the pre-ground function selected,
pre-ground coffee has not been poured into
the funnel.
Place pre-ground coffee in the funnel or
deselect the “pre-ground”function (fig. 17).
DESCALE
The machine must be descaled.
The descaling procedure described in the
section “Descaling” needs to be performed as
soon as possible (page 17).
LESS COFFEE
Too much coffee has been used.
Select a milder taste by pressing the dial
(fig. 9) or reduce the quantity of pre-ground
coffee.
FILL BEANS CONTAINER
The coffee beans have run out.
Fill the beans container (fig. 13).
The pre-ground coffee funnel is clogged.
Empty the funnel with the help of a brush as
described in the section “Cleaning the pre-
ground coffee funnel”.
INSERT INFUSER ASSEMBLY
INSERT TANK
The infuser has not been replaced after
cleaning.
Insert the infuser as described in the
paragraph “Cleaning the infuser”.
The tank is not correctly in place.
Insert the tank correctly and press as far as it
will go.
20
GENERAL ALARM
The inside of the appliance is very dirty.
Clean the inside of the appliance thoroughly,
as described in the section “Cleaning and
maintenance”. If the message is still displayed
after cleaning, contact a service centre.
EMPTY CIRCUIT FILL CIRCUIT The water circuit is empty.
alternating with
Hot water press OK
Press OK to deliver water from the spout (A14)
until it flows out normally.
REPLACE FILTER
The water filter is exhausted.
Replace the filter or remove it as described in
the section “Water filter”.
SET DIAL TO CLEAN
INSERT WATER SPOUT
INSERT MILK CONTAINER
Milk has been delivered recently and the tubes Turn the froth adjustment dial to CLEAN.
inside the milk container must be cleaned.
The hot water spout is not inserted or is Insert the water spout (D3) as far as it will go.
inserted incorrectly.
The milk container is not inserted correctly.
Insert the milk container (fig. 21) as far as it
will go.
TROUBLESHOOTING
Below is a list of some of the possible malfunctions.
If the problem cannot be resolved as described, contact Customer Services.
PROBLEM
POSSIBLE CAUSE
SOLUTION
The coffee is not hot
The cups were not preheated.
•
Enable the cup warmer, leave the cups at
least 20 minutes to warm up.
Warm the cups by rinsing them with hot
water (N.B. you can use the hot water
function).
•
The infuser has cooled down because Before making the coffee, warm the infuser by
2/3 minutes have elapsed since the last using the Rinsing function to perform a rinse
coffee was made.
cycle (page 10).
Low coffee temperature is set.
The coffee is ground too coarsely.
In the menu, set a higher coffee temperature.
The coffee is thin or not creamy
enough.
Turn the grinding adjustment dial one click an-
ticlockwise towards “1” while the coffee mill is
in operation (fig. 12).
Continue one click at a time until coffee delive-
ry is satisfactory. The effect is only visible after
delivering 2 coffees (see the section:“adjusting
the coffee mill”on page 12).
The coffee is unsuitable.
Use pre-ground coffee for espresso coffee ma-
kers
The coffee is delivered too slowly or a The coffee is ground too finely.
drop at a time.
Turn the grinding adjustment dial one click
clockwise towards “7” while the coffee mill is
in operation (fig. 12).
Continue one click at a time until coffee delive-
ry is satisfactory. The effect is only visible after
delivering two coffees. (see the section “adju-
sting the coffee mill”on page 12).
21
Coffee does not come out of one of
the spouts.
The spouts are blocked.
Clean the spouts with a toothpick (fig. 29B).
The milk does not
come out of the milk
spout.
The milk container lid is dirty.
Clean the milk container lid as described in
the section “Cleaning the milk container”.
The milk contains
large bubbles and
squirts out of the
milk spout or there
is little froth .
the milk container lid is dirty.
Clean the milk container lid as described in the
section “cleaning the milk container”.
the milk is not cold enough or is not Use skimmed or semi-skimmed milk at refrige-
semi-skimmed.
rator temperature (about 5° c).
If the result is not as you wished, try changing
brand of milk.
The froth adjustment dial is incorrectly Adjust following the instructions in the section
adjusted. “making drinks with milk”.
The milk container lid or froth Clean the milk container lid and dial as de-
adjustment dial is dirty
scribed in the section “cleaning the milk con-
tainer”.
The milk contains
large bubbles there
is little froth .
The hot water/steam nozzle is dirty
Clean the nozzle as described in the section
“cleaning the hot water/steam nozzle”.
The appliance does not come on.
The infuser cannot be extracted
The spout is dirty.
Clean as described in the section “Cleaning the
spout after use”.
It is not plugged into the mains socket. Plug into the mains socket.
The main switch (A7) is not turned on. Place the main switch in the i position (fig. 2).
The appliance has not been turned off
Turn the appliance off by pressing the
ton (pag. 9).
but-
correctly
22
ELECTRICAL CONNECTION (UK ONLY)
Before using this appliance ensure that the voltage indicated on the product corresponds with the main voltage in your home, if you
are in any doubt about your supply contact your local electricity company.
The flexible mains lead is supplied connected to a B.S. 1363 fused plug having a fuse of 13 amp capacity.
Should this plug not fit the socket outlets in your home, it should be cut off and replaced with a suitable plug, following the proce-
dure outlined below.
Note: Such a plug cannot be used for any other appliance and should therefore be properly disposed of and not left where children
might find it and plug it into a supply socket - with the obvious consequent danger.
Please note: We recommend the use of good quality plugs and wall sockets that can be switched off when the machine is not in
use.
IMPORTANT: The wires in the mains lead fitted to this appliance are coloured in accordance with the following code:
Green and Yellow to Earth
GREEN AND YELLOW
BLUE
BROWN
EARTH
NEUTRAL
LIVE
13 amp Fuse
Brown to live
Cord Clamp
Blue to
neutral
As the colours of the wires in the mains lead of this appliance may not correspond with the coloured markings identifying the
terminals in your plug, proceed as follows:
-
The wire which is coloured green and yellow must be connected to the terminal in the plug which is marked with the letter E or
by the earth symbol or coloured green or green and yellow.
-
-
The wire which is coloured blue must be connected to the terminal which is marked with the letter N or coloured black.
The wire which is coloured brown must be connected to the terminal which is marked with the letter L or coloured red.
When wiring the plug, ensure that all strands of wire are securely retained in each terminal. Do not forget to tighten the mains
lead clamp on the plug. If your electricity supply point has only two pin socket outlets, or if you are in doubt, consult a qualified
electrician.
Should the mains lead ever require replacement, it is essential that this operation be carried out by a qualified electrician and should
only be replaced with a flexible cord of the same size.
After replacement of a fuse in the plug, the fuse cover must be refitted. If the fuse cover is lost, the plug must not be used until a
replacement cover is obtained. The colour of the correct replacement fuse cover is that of the coloured insert in the base of the fuse
recess or elsewhere on the plug. Always state this colour when ordering a replacement fuse cover.
Only 13amp replacement fuses which are asta approved to B.S. 1362 should be fitted.
This appliance conforms to the Norms EN 55014 regarding the suppression of radio interference.
Warning - this appliance must be earthed
23
|
Lindy 70539 User Manual
Lenovo 1184 User Manual
i mate Ultimate 6150 User Manual
Helio Ocean User Manual
Gemini CDS 2000 User Manual
FieldServer FS 8700 80 User Manual
Emerson CKS9031 User Manual
AT&T F160 User Manual
Alpine IVA D300 User Manual
2Wire Epson Stylus Photo RX500 All in One Printer C11C544001 User Manual